23rd Brazilian Conference on Materials Science and Engineering

Preface
Chapter 1: Composite Materials
Evaluation of the Influence of Pre-Alloyed Powder Fe65Nb on the Production of Metal Matrices by Powder Metallurgy
Elastic Wave Propagation in a Bio-Inspired Phononic Crystal
Tensile Properties of Epoxy Matrix Reinforced with Fique Fabric
Comparison of Mechanical Properties of Banana Fibers Reinforcement in Different Thermoset Matrix Composites
Novel Sustainable Composites with Geopolymeric Steel Slag and Recycled from Packing PET
Evaluation of PP/Wood Flour Composite Processing Using Computer Simulation
Influence of Mercerization Process on the Surface of Coconut Fiber for Composite Reinforcement
Influence of Degradation on the Ballistic Behavior of Aramid Fabric Reinforced Polymeric Armor Composites
Chapter 2: Polymeric Materials
Evaluation of the Mechanical Behavior of Bisphenol-A Polycarbonate after Thermal Degradation
Influence of Glycerol Content on the Physic-Chemical and Mechanical Properties of Cassava Starch Films
Influence of the Order of Incorporation of Sulfur in the Mechanical Properties of Vulcanized Nr Compounds
Comparative Study of the Degradation of the Green HDPE and Petrochemical HDPE in the Primary Recycling
Evaluation of Low-Density Polyethylene Thermomechanical and Fractographic Behavior after Ultraviolet Radiation Exposure
Preparation and Characterization of Polysulfone / Recam® Composite Membranes for Potable Water Production
New Applications of Tire Powder Recycled by Micro-Waves
Quasi-Static and High Strain Rate Uniaxial Compressive Response of Recycled Polycarbonate from Industrial Waste
Study of Mechanical Behavior of Polycarbonate after Thermal Degradation
Evaluation of Temperature Influence on Tensile Strength and Izod Impact Resistance on Poly Methyl Methacrylate (PMMA)
Chapter 3: Materials for Electrochemical and Photovoltaic Application
Influence of Separator Thickness on the Performance of Electric Double Layer Supercapacitors in Aqueous Electrolyte
Study of Supercapacitors for Use in Dye Sensitized Solar Cells
Effect of the Heat Treatment on the Microstructure and Morphology of Cigs Thin Films Prepared by RF Magnetron Sputtering at Room Temperature
The Effect of Vacuum Annealing and HDDR Processing on the Electrochemical Characteristics of Activated Carbon and Graphene Oxide for the Production of Supercapacitors Electrodes
Effects of Electrolyte Substitution on the Specific Capacitance and Equivalent Series Resistance of Energy Storage Electrochemical Supercapacitors
Study of CaF2- Doped PbTe Thin Films Grown by Molecular Beam Epitaxy
Low-Temperature Reduction of Graphene Oxide Using the HDDR Process for Electrochemical Supercapacitor Applications
Influence of the Electrolyte Potential Window on the Electrical Characteristics of Supercapacitors Operating Elevated Temperatures
The Influence of the Addition of rGO and CNT on the Electrochemical Properties of the Batteries the LaNi-Based Battery Alloys
Graphite Electrodes for Hydrogen Production by Acid Electrolysis
Chapter 4: Functional Ceramics and Metal Oxides
Impact of ZnO Concentration on the Stability of Agglomerates of TiO2 Engineered Nanoparticles: Effects of the pH, Ionic Strength and Zeta Potential
Evaluation of the Influence of the Reaction Medium of the Microstructure of Magnesium Oxide Nanopartícles
Thickness Estimation of TiO2-Based Nanotubes Using X-Ray Diffraction Techniques
Microstructural Analysis of Zinc Niobate Ceramics Processed by Microwave Thermal Treatment
Sintering Behavior of AL2O3 Ceramics Doped with Pre-Sintered NB2O5 and LiF
Novel Alumina Compounds with Niobia, Silica and Magnesia for Ballistic Armor
Processing, Characteristics and Properties of Cubic Boron Nitride - An Updated Review
Characterization of Nanostructured Mn-Zn Ferrites Synthesized by Coprecipitation Method Using CTAB
Chapter 5: Structural Ceramics
Waste of Civil Construction for Use in Mortar and Production of Structural Concrete
Limestone Waste Incorporation in Clayey Mass for Rustic Ceramic Tiles Manufacturing
Water Absorption and Transport in Clay Bricks
Use of Ceramic Waste for the Manufacture of Sintered Parts
Microstructural Characterization of Slag Residue Incorporated into Clay for Production of Red Ceramics
Recycling of Steel-Making Plant Waste into Heavy Clay Ceramic- Industrial Test
Effect of the Incorporation of Marble Waste in the Properties of Clay Ceramic Bricks
Study of the Potential of Adhesion to the Substrate of Masonry and Tensile in the Flexion in Mortars of Coating with Gray of the Sewage Sludge
Addition of Ornamental Rock Residues on Ceramic Blocks: Physical and Chemical Analysis
Behavior of Mortar with the Addition of Sugar Cane’s Ash Residues
The Use of Thermogravimetric Analysis to Characterize the Metallic Slag Aggregates in Structural Concrete
Selective Laser Sintering of Biomaterials and Composites State of the Art and Perspectives
Citric Acid Effect in High early Type Portland Cement Pastes and Mortars
Chapter 6: Steels and Alloys
Equal Channel Angular Pressing Consolidation and Heat Treatment of Blended Elemental Powders of Fe-Mn-Al
Effect of Post-Weld Heat Treatment on Hardness in Superduplex Stainless Steel ASTM A890/A890M - Grade 6A
Microstructural Characterization and Mathematical Modeling for Determination of Volume Fraction of Eutectoid Mixture of the Cu-8.5wt% Sn Alloy Obtained by Unidirectional Upward Solidification
Influence of the Thermal Parameters on the Microstructure, Corrosion Resistance and Hardness on the Unidirectional Solidification of Al-10wt% Si-5wt% Cu Alloy
PrFeB Based Alloys Obtained by Melt Spinning for the Production of Permanent Magnets
Mechanical Resistance of High-Speed Steels Cr-W-Mo-V, Si-Mn-Cr-Mo-V-Co, Si-Mn-Cr-Mo-V and Si-Mn-Cr-Mo-V-Co Heat Treated
AISI 310 Stainless Steel Formed by Gelcasting: An Alternative Manufacturing Method
Influence of the Deep Cryogenic Treatment at the Phase Transformation Temperatures and at the Stabilization of the Cu-14Al-4Ni SMA Alloy
Thermal Transformations of the Nickel Laterite Agglomerate Phases and their Metallurgical Influence
Obtention of Nb47Ti and Ti13Nb13Zr Alloys Powders by Hydride-Dehydride Process for Additive Manufacturing Applications
Characterization and Evaluation of Mechanical Properties and Residual Stress in Aluminum-Magnesium Alloys Welded by the FSW Process
Microstructural Characterization of Joints of Inconel 718 Brazed on Vacuum Furnace
Equal Channel Angular Pressing and Characterization of a Patented Eutectoid Fe-C Steel
The Influence of the Microstructure of an HHA Steel on the Formation of Adiabatic Shear Bands, after High Deformation Rates
Study of Superioring of a Seal Soldered by Tig Process of the Aluminum League 6061
Promising Ballistic Behavior of CoCrFeMnNi High Entropy Alloy
Chapter 7: Corrosion Behavior, Protective Coatings and Surface Engineering
Study of the Corrosion of Carbon Steel (SAE 1020) Coated with Niobium Oxides
Inhibitory Action of Persian Pyrifoliabark Extract against Corrosion of SAE 1020 Carbon Steel in Sodium Chloride Medium
Electrochemical Corrosion Behavior of Iron Aluminides in Sulfuric Acid
Study of Corrosion Behavior of Friction Surfacing AA6351 Aluminium Alloy Coating on AISI 1020 Low Carbon Steel
Study of Corrosion of AA 3003 Aluminum in Biodiesel, Diesel, Ethanol and Gasoline Media
Calibration of the AC Potential Dropping System (ACPD) for Determination of Crack Growth in API 5L X65 Steel under Cathodic Protection Effect
The Influence of Temperature on the Tribological Properties of the Ti6Al4V Alloy Treated by Plasma Oxidation
Influence of the Electrolyte Composition on the Corrosion Behavior of Anodized AZ31B Magnesium Alloy
Quantitative Analysis of the Sensitization of an Austenitic Stainless Steel Aged between 600 and 900°C through Electrochemical and Microstructural Measurements
Laser Welding Influence on Corrosion Rate of Galvanized Sheets of DP600 Automobilistic Alloy
Influence of Roughness on Corrosion Resistance of Carbon Steel SAE 1020 and DOMEX® 700 MC Steel
The Chemical Deposition of Polypyrrole at a Copper Surface Varying Concentrations of Salicylic Acid in the Reactive Medium
Metallic Surface Coating of Polymeric Parts Produced by Additive Manufacturing Process
Chapter 8: Biomedical Materials and Applied Biotechnologies
Analysis of the Pullout Testing of Straight and Angled Abutments in Narrow Diameter Implants
Microstructural Characterization and Mechanical Properties of As-Cast Ti-12Mo-25Nb Biocompatible New Alloy
Failure Analysis of Metallic Orthopedic Implant for Total Knee Replacement
Modifications of Titanium and Zirconium Alloy Surfaces for Use as Dental Implants
Study of the Feasibility of Biodiesel Production, from Vegetable Oils and Catalysts of Seafood Residues, in a Batch Hydrogenation Reaction Unit, Assisted by Microwave and Conventional Heating
Physical-Chemical and Thermal Characterization of Powder Eucalyptus Bark
Manufacturing Techniques: Polymer Implants as Drug Delivery Systems for Cancer Therapy
Antimicrobial Activity of the Sodium Lauryl Sulphate Used as Surfactant in the Polymeric Encapsulation Processes
Production and Characterization of the Ti-12Mo-30Nb Alloy