Properties and Testing Techniques of Inorganic Materials II -

Properties and Testing Techniques of Inorganic Materials II

Buch | Softcover
624 Seiten
2017
Trans Tech Publications Ltd (Verlag)
978-3-03835-787-2 (ISBN)
359,95 inkl. MwSt
  • Keine Verlagsinformationen verfügbar
  • Artikel merken
7th TEIM 2016


Selected, peer reviewed papers from the Seventh Annual Meeting on Testing and Evaluation of Advanced Materials, April 20-22, 2016, Xi'an, China
This book comprises papers presented in the Seventh Annual Meeting on Testing and Evaluation of Advanced Materials, which was held from April 20 to 22, 2016, in Xi'an, China. Collected papers covered most aspects of analysis techniques for chemical composition and microstructures, testing techniques on mechanical, chemical, and physical properties of advanced materials (mainly inorganic materials, including ceramics, glasses, concretes, synthesized crystals, etc.) and reflects the newest developments in these fields in China.

Preface, Organizing Committee, Sponsor
Chapter 1: Technique and Methods for Testing and Analysis of Materials
Effect of Preparation Process on Bending Modulus and Strength of Fiber Tubes in Radial Direction
An Improved Cross-Bonded Method for Measuring Interfacial Bond Strength of Adhesives
An Introduction to Dynamic Load Test on Photovoltaic Modules
Research of Nominal Operating Temperature Testing Method of BIPV Module
The Analysis of Influence Factors in Cement Strength Test
New Characterization Method of Hot Metal Penetration Resistance for Blast Furnace Carbon Blocks
Characterization of Test Methods of Capillary Pressure of Cement-Based Materials
Analyze of the Stress-Birefringence of the Fused Silica with Large Aperture
Determination of Phthalate Esters in Plastic Track Surface Layer Material by Gas Chromatography
Fluoride Determination by Ion Chromatography in Fluorocarbon Coatings
Composition Analysis of an Unknown Redispersible Powder
Correction of Loss on Ignition in Slag Powder by ICP-AES
Determination of ZrO2 and TiO2 in Alkali-Resistant Fiberglass Mesh by ICP OES
ICP-AES Determination of Sulfide and Sulfate Content in Pebble and Crushed Stone
Ion Chromatography for the Continuous Determination of Sulfite and Sulfide in Gypsum and Gypsum Products
Preliminary Discussion of the Detection Method for Asbestos
Measurement of Multilayer Film Thickness Using X-Ray Fluorescence Spectrometer
Rheological Measurement of In Situ Preheating Polycarbosilane Melt
Determining Zero Shear Viscosity of Polycarbosilane Melts
Determining Anisotropic Young’s Modulus of Ceramic Coatings by the Relative Method
Measurement for Elastic Modulus of Ultra-Thin Glass by Cantilever Beam Method
Evaluating Thermal Expansion Coefficient of SiC Coatings by Relative Method
Monitoring Early Hydration of Concrete with Ground Penetrating Radar
Patent Analysis of Concrete Testing Technology
Chapter 2: Advanced Ceramics and Inorganic Composites
Structure and Characteristics of Carbon Nanotube Reinforced SiC Composite
The Effect of Heat Treatment on the Microstructure and Mechanical Properties of KD-II SiC Fibers in Air
Effects of Fiber Pre-Oxidation on Mechanical Properties and Microstructure of T700 Carbon Fiber Reinforced Mini C/SiC Composites
Microstructure and Mechanical Properties of ZrB2-SiC-ZrSi2 Composites Fabricated by Spark Plasma Sintering
Oxidation Behavior of Si-B-C-N Multiphase Ceramic
The Effect of Point Defects Induced by Fast Neutron Irradiation on the Thermal Conductivity of Boron Carbide
Boron Carbide Hollow Microspheres Prepared by Polymer Derived Method
Influence of Synthesis Process on Coated Properties of Al(OH)3-Y(OH)3/ZrB2 Composite Powders
Rheological Properties and Ceramization Mechanism of ZrO2 Preceramic Solution
Research on Optical Property of Black-Colored Zirconia Ceramics by Photoluminescence, Raman and Visible Reflectivity Spectra
Microstructures and Mechanical Properties of Y2O3 Ceramics
Preparation of Superfine Alumina Powders via Hydrothermal Method
Densification Mechanism of Al2O3/Al Metallic Ceramics Prepared via Powder Metallurgy Method
Mechanism of Controlled Pore Structure of Quartz Pore Gradient Materials
Synthesis of Silica Aerogel Using Silica Sol by Ambient Drying Method
Synthesis and Characterization of Pd/Ag/SiO2 Nano-Composite Materials
Preparation and Microwave Dielectric Properties of xBaZn2Ti4O11-(1-x)BaNd2Ti4O12 Ceramics
Effect of Nd2O3 on the Microwave Dielectric Properties of 0.67CaTiO3-0.33LaAlO3 Ceramics
Sintering Behavior and Microwave Dielectric Properties of Li2O-B2O3-SiO2 Doped 0.67CaTiO3-0.33LaAlO3 Ceramics
Domain Walls and Thermal Aging Stability of (K,Na)NbO3-Based Ceramics in Tetragonal Phase
Reflectivity and Laser Ablation Behavior of La1-xSrxTiO3+δ Coating
Effect of Pore Size on Partial Discharge in Ultra-High Voltage Ceramic Capacitors
The Investigation of Perovskite LaCo0.6Ni0.4O3-δ as Cathode Interface Contact Material for Intermediate Temperature Solid Oxide Fuel Cells
Synthesis and Conductivity Investigation of Cu Doped Apatite Type Lanthanum Silicate Electrolyte
Influence of Different Gd3+ Doping on the Upconversion Luminescence Properties and Morphology of NaYF4:Yb,Er
Investigation on the Preparation and Properties of Monodispersed Spherical Y2O3:Dy3+ Phosphor
Investigation on Synthesis and Property of Tb3+/Dy3+ Co-Doped Gd3Al5O12 Phosphor
Photoluminescence Properties of SrSi2O2N2 Doped with Divalent Ytterbium Phosphor in Nitrogen-Rich Coordination
Surface Morphology and Phase Transitions of Anodic TiO2 Films Induced by Hydrothermal Exposure
Measurement and Characterization of CeO2-TiO2 Ion Storage Films for Electrochromic Devices
TA Assisted Synthesis and Properties of Porous ZnO
Influence of CeO2 Doping on Property of SnO2 Ceramics
Effect of the Ratio of Co to Ni+Co on the Microstructures and Mechanical Properties of Ti(C, N)-Based Cermets
Hot-Press Sintering of Tic0.5N0.5-Based Cermets: Addition Effect of AlN Nano-Powder on Microstructure and Mechanical Properties
Effect of Deposition Time on Hardness and Bonding Strength of Magnetron Sputtered TiN Coatings on 316 Stainless Steel
Controlled Preparation and Characterization of Titanium Series Functional Pigment and its Application in Coatings
Comparison of Mo-10Nb Alloy Target Materials Prepared by Different Techniques
Chapter 3: Nanomaterials and Applied Nanotechnology
The Electrochemical Deposition of Fe Nanowires and the Influence of Current Density on the Deposition Rate
Fluorescence Enhancement of Europium-Doped Yttrium Oxide Nanosheets Modified by HTTA
Heterojunction Structure ZnO/TiO2 Nanorods with Enhanced Photoelectrochemical Properties
Application of Improved BP Neural Network in the Preparation Processing of the CaCO3 Nanocrystalline
Chapter 4: Materials and Technologies in Environmental Engineering and Chemical Production
Bentonite-Copolymer Composite for Removing Basic Fuchsin
The Preparation of Magnesium Hydroxide Whiskers
Determination of Formaldehyde in Water-Borne Coatings by HPLC
Facile Synthesis and Photocatalytic Performance of W18O49 Nanorods
Effect of Reaction Time on the Morphology and Photocatalytic Property of ZnO Nanoparticles
Chapter 5: Glass and Refractories
Preparation of Hollow Fiber Membrane Precursor from Glass and PVDF by Non-Solvent Induced Phase Separation
Laser Induced Damage in Fused Silica for 248 nm
Microstructural Study on the Low Density SiO2 Soot Body
Glass Surface Stress Measurement and Digitalization
Properties Characterization of MgO-Cr2O3-ZrO2 Brick Prepared by Vacuum Impregnation
Effects of Sintering Temperature on Phases, Microstructures and Properties of Fused Silica Ceramics
Deep Wet Etching Uniformity of Polished Fused Silica Glass
Influence of Ionizing Gas Flow on Structural Homogeneity of Type IV Silica Glass
Analysis of the Test Method of Quartz Glass Optical Homogeneity
Test and Analysis of Hydroxyl Group in CVD Synthetic Silica Glass
Flame Temperature Distribution and SiO2 Particles Distribution in Oxyhydrogen Flame
The Effects of Surface Treatments, Compression Speeds and Sample Sizes on Compression Load and Strength of Foam Glass
Determination of Chemical Composition in Zircon-Refractory Material by MLD Method
Effect of Additives and Carbon Resources on Thermal Shock Resistance of Spinel-C Material
The Improvements for the Siliceous Self-Flow Castable with Adding Nano SiO2
Application of Electromagnetic Field Theory in the Study of Iron-Rich Slag Resistance Mechanism of Low Carbon MgO-C Refractories
Effects of Matrix Densification Based on Particle Packing on Lightweight Al2O3-MgO Castables
Application of Molten Salt Method in Hercynite Composite Powder Synthesis at Elevated Temperature
Study of Three-Dimensional Optical Homogeneity of Fused Silica Prepared by Chemical Vapor Deposition
Preparation and Anisotropic Lattice Thermal Expansion of Hexagonal Cordierite
Chapter 6: Building Materials
Research Progress of Plugging Agent in Construction Engineering
Primal Study on Mechanical Properties of Phosphate Based Geopolymer
Redispersible Polymer Powder-Modified Sulphoaluminate Cement Mortar
The Restoration of Compressive Strength of Self-Healing Mortar
Water Absorption and Hydration Products of Metakaolin Modified Mortar
Preparation and Mechanical Performance of Sulpoaluminate Cement by Using Industrial Solid Wastes
Activity Evaluation of a Tailing in a Cementitious System
Shrinkage Properties of Cement-Silica Fume Blended Pastes in Early Age
Polymer-Modified Cement Waterproofing Coating and Cementitious Capillary Crystalline Waterproofing Materials: Mechanism and Applications
Study on the Influence of Stone Dust on Adaptability of Polycarboxylate Superplasticizer and Cement
The Effect of Concrete Mix Proportion to the Air Bubble Spacing Coefficients of Hardened Concrete
The Room Temperature Synthesis and Performance Study of Cationic Polycarboxylate Superplasticizer
Experimental Study and Numerical Analysis on Chloride Diffusion Coefficient of Concrete with Various Water-Cement Ratios
Fracture Properties of Ultra-High Strength Cement-Based Materials
Study on the Reduction of Radon Exhalation Rates of Concrete with Different Activated Carbon
Identification of Fe-Containing Phase in Oxidation Process of BOF Slag
Dynamic Hydrothermal Synthesis of Super-Low Density Xonotlite Thermal Insulation Materials from Industrial Quartz Powder
Static Modulus of Ettringite in Different Environment
The Effect of Pore Structure and Water Absorption on Carbonation Resistance of Sulphoaluminate Cement Foam Materials
Effect of Surface Vitrification on the Properties of Insulation Board of Expanded Perlite
Test and Optimal Design of New Type Aluminum-Plastic Composite Panel

Erscheinungsdatum
Reihe/Serie Key Engineering Materials
Zusatzinfo Illustrations, unspecified
Verlagsort Zurich
Sprache englisch
Maße 170 x 240 mm
Gewicht 1180 g
Themenwelt Naturwissenschaften Chemie Anorganische Chemie
Technik Maschinenbau
ISBN-10 3-03835-787-1 / 3038357871
ISBN-13 978-3-03835-787-2 / 9783038357872
Zustand Neuware
Haben Sie eine Frage zum Produkt?
Mehr entdecken
aus dem Bereich

von Erwin Riedel; Christoph Janiak

Buch | Hardcover (2022)
De Gruyter (Verlag)
92,95